10 watts 8 ohms class d amplifier pam8610 sound test

-

Pam8610 IC is 10 watts @ 8 ohms (15 watts @ 4 ohms small heat sink require) stereo class d amplifier with very high efficiency over 90% and the amplifier works well without any heat sink at full power!!! .

The amplifier board is very low cost ( around 1 $) but deliver 10 watts @ 8 ohms power from 13 volts power supply.
As you can see in my video that the amp board require only one 100 uf electrolytic capacitor for supply decoupling to eliminate hum from switching power supply(some ic amplifier require 1000 uf to eliminate hum from the power supply).

Sound testing:

The amplifier sound good with good bass respond  good bass impact and well control (kick bass very good). High frequency clean, impact well and flat but lack transparent. Singer vocal is clean but not transparent. The sound stage is wide but space between instrument not precise. pam 8610 amp board is the quiet amp with very less hiss noise (5 cm away from tweeter to my ear :) which is not a big problem at all and the amp do not oscillate with 1.5 meters speaker wire, not like some class d board amp.

PAM 8610 specification

Power Range: DC 7.5V-15V ( can power the amp from car and motorcycle batteries)
Recommended voltage: DC 12V(3A)
Output Power: 10W x 2(8Ω) 15Wx2(4Ω)
Frequency Response: 20HZ-30KHZ(-1 db)
queinsent Current: 20 mah (DC12V)
SNR: - 90 dbs

 See sound test with JVC loudspeaker.
I use Olympus e-pm2 camera built-in stereo microphone to record sound and video resolution is @1080p

The amplifier board is very tiny 1"x1"dimension.

 If you want low-cost but high-quality board amplifier TA 2024 class t amplifier  is a good choice for you. Find TA2024 amplifier here
http://www.easyandworkproject.xyz/2016/02/15-watts-stereo-class-t-amplifier-sound-test-review.html

See how to connect volume control to PAM 8610 amplifier board here
http://www.easyandworkproject.xyz/2016/07/how-to-connect-amplifier-to-volume.html

 See how to add a power supply filter capacitor to PAM8610 amp board to improve the amp board sound here
http://www.easyandworkproject.xyz/2016/07/how-to-add-capacitor-to-amplifier-board.html


Hope you enjoy.
Pam 8610 board amplifier.

Comments

  1. Amamam12/15/16, 1:08 AM

    How should I use this one with 4ohms speakers? Thank you.

    ReplyDelete
    Replies
    1. esw12/15/16, 6:47 PM

      According to datasheet
      THD+N = 0.1%, f = 1kHz, RL = 4Ω (Note 3) 15 W

      Note: 3. Heat sink is required for high power output.

      Yes!!! you can use it without problem, if you play loud music your board-amplifier need a small heatsink attach to pam8610 chip

      Delete
    2. Unknown12/16/16, 2:56 PM

      Does It matter if I chose a 50v 100 uf electrolytic capacitor or a 35v model. Or is a noteer model needed?
      Thx

      Delete
    3. esw12/16/16, 7:02 PM

      If you feed the pam8610 board with 12 volts dc, you need capacitor voltage value at least 16 volts. Using high voltage rate capacitor doesn't effect sound quality and make the cap's life longer but the higher voltage model cost is higher.

      Delete
  2. Unknown11/3/17, 2:40 PM


    Hi, I'm having problems with this amplifier and I saw your video, could you help me please? my pam8310 goes off when it plays a deep bass and turns on again, I do not know what's going on, with low volume works perfect but when I increase the volume goes off
    I wait for your answer thanks :)

    ReplyDelete
    Replies
    1. esw11/4/17, 9:07 PM

      Provide me some information.
      how many ohms loudspeaker?
      how many ampere of your adaptor?

      Normally, if you play loud music with deep bass with low impedance loudspeaker, you amplifier work hard and may activate built-in thermal protection.

      Delete
    2. Unknown2/11/18, 5:55 PM

      I am also having the same problem.. whenever i try to increase my volume its goes off and then restars itself.. why is this happening.

      I am using...

      1. 12 volt 2 amp adapter
      2. 2 piece 10 watt 8 ohm speaker (also tried 2 piece 15 watt 4ohm speaker)

      Please help me!

      Delete
    3. esw2/11/18, 11:54 PM

      1 Don't boost bass too much.
      2 Check adapter it may has high AC ripple
      3 Sometimes, the Pam 8610 ic design board has poor heating transfer performance or not pass qc.

      The first solution is easy to check, lower bass in equalizer and test again

      Delete
  3. accountingstudypoint2/7/21, 4:20 PM

    CAN I USE 6 SPEAKER 8OHMS 8WATT in one PAM 8610

    ReplyDelete
  4. Darshit Pantrawala2/2/22, 10:35 PM

    What is the value of attached capacitor and what is the use of it?

    ReplyDelete
    Replies
    1. esw3/14/22, 11:53 PM

      100 uf capacitor. It make current feed to amplifier faster than the bigger one alone for better transient.
      Change the cap with different brand and you may hear sound character different like me ( nichicon for bass and treble boost, elna cerafine, elna silmic for softer sound).

      Delete

Post a Comment

Popular posts from this blog

Resistor color code

-
Image
A resistor is the most important electrical component in almost every electronic circuit, it can limit current to any load such as led, transistor, op-amp, etc.  We must read the resistor color code if we want to know the resistive value, tolerance, temperature coefficient. Resistors have different color bands (3,4,5,6) the more color bands the more resistor information. Now let's start with 3 bands resistor color code. The above resistor has only 3 bands First digit, Second digit, and multiply. A 3 bands resistor color code has a fixed +/- 20% tolerance which means if the color code value is 1,000 ohms the real-life resistive value may be +/- 200 ohms.  4 band resistor color code A 4 bands resistor color code has a tolerance value color strip, the resistor on the above picture has 5% tolerance. This type of resistor uses in a regular circuit such as television, radio, washing machine. 5 bands resistor color code A 5 bands resistor colo...
Read more

How to add power supply filter capacitor to amplifier board.

-
Image
I saw a new comment on my video, he asked me how to add a filter capacitor to amplifier board D.C. power supply. I think it's a good question so I will explain it here. What is a power supply filter capacitor? It is the capacitor that used to filter AC ripple from DC power supply present to amplifier board. If an amplifier has low capacitive power supply capacitor, it may present a little hum(50/60 Hz low-frequency sound) that you can hear in a quiet room. The capacitor also stores power and bring it instantly to your amplifier when an amplifier needs more power for a short period of time such as  explosion sound in a movie. However, If an amplifier has high-frequency power supply noise from a switching power supply, small capacitor need to parallel to a power supply and must be attached close to power amplifier IC as much as possible. Below pictures are the place that you add power supply capacitor. PAM 8610 board amplifier powe...
Read more

Infrared proximity sensor circuit diagram

-
Image
An infrared proximity sensor is a sensor that detects any object when it close to the sensor. The circuit is an important part of an automatic faucet, robot, and touchless switch. An above image is an infrared proximity sensor circuit diagram. The circuit is simple and easy to make, it has 2 transistors, 4 resistors, an IR LED, an IR phototransistor, and a purple or white or green LED (use as an indicator so you can remove it if you want) Electronic components list This circuit's maximum detection range is 10 centimeters, you can decrease the detector range by changing R2 resistor. Use 7805 regulator IC if you want to use the circuit with 12 volts power supply. The infrared proximity sensor consumes around 50 milliamps per hour when standby and consumes around 80 milliamps(add a relay that consumes 30 milliamps) so you need an external power supply because battery life will not last long. The reason that makes this circuit consume much energy because IR LED n...
Read more

How to connect volume control to an amplifier

-
Image
I saw a comment on my Youtube video, he asked me how to connect any amplifier module to a volume control or potentiometer. I think so many people who want to start an electronic project must know this basic wiring too, I hope this wiring diagram will help an electronic DIYer like me. First thing you need to know: use shield wire for an input signal to volume control and from volume control to amplifier if you don't want you amplifier suffers from parasitic oscillation (sound like JeeeeJeeeee). keep a wiring as short as possible. use low resistive value volume control (5-10 kilo-ohms) if the amplifier has random parasitic noise when you turn a volume control up or down. volume control is a potentiometer. Volume control principle is a signal divider, the more volume control output(yellow line) near input signal source(pink line) the most signal flow to an amplifier. When you lower a volume control the resistive va...
Read more

simple bass booster circuit diagram

-
Image
This bass boost diagram is easy to build and work well, I made it because people asked me the schematic diagram of bass boost diagram on my youtube channel. The circuit has 9 dB gain@40 Hz that mean you will get good bass performance even you play music to a small speaker. Why this circuit doesn't look like circuits on the internet? Almost every circuit on the internet uses R/C filter between pre-amp and power amp stage to bypass high frequency to a ground and that seems audio signal being amplified and bypass to ground. I think it wastes pre-amplifier gain, the more gain preamp stage the more distortion to the audio signal, so I use a capacitor to send more negative feedback to pre-amp negative input when the frequency higher than cut-off frequency, capacitor impedance(resistance) higher when frequency lower and that make negative feedback decrease when frequency lower. An op-amp distortion lowers when negative feedback higher, that mean high-frequency disto...
Read more

how to repair water damage particle board

-
Image
This video shows you how to repair water-damaged particle boards. A particle board is light and cheap so furniture manufacturers use it widely, but it swells quickly if it exposes to water or moisture and it will be worse if you don't repair it fast. This video shows step by step guide and I hope you like it.
Read more

Humidity sensor with led alarm | Arduino project

-
Image
This page contains Arduino Humidity sensor with led alarm source code. This project is good for someone who wants to make a humidity meter or hygrometer with led alarm if humidity and temperature over a threshold. It's easy to make and doesn't require an external power supply, just use power from an Arduino UNO R3 board (USB power compatible with this project). Electronic components list: 1 x Arduino Uno R3 1x 20 x4 I2C LCD display 1 x AM 2320 humidity/temp sensor 1 x 5 mm led ( 2 x if you plan to use led for pin 13 instead built-in led) 1 x 1000 ohms resistor ( 2 x if you plan to use led for pin 13 instead built-in led) Any USB power adapter, 500 mA current at least. Here is the Arduino code: AM 2320 library  https://github.com/hibikiledo/AM2320 LCD display i2c library  https://github.com/fdebrabander/Arduino-LiquidCrystal-I2C-library #include <Wire.h> #include <AM2320.h> #include <LiquidCrystal_I2C.h> LiquidCrystal_I2C lcd(0x3...
Read more

lm3914 schematic diagram and test

-
Image
If you want to make a simple VU meter. LM3914 is the best choice for you. It's easy to make VU meter or 10 dot/bar DC level meter with lm3914.  lm 3914 can withstand +-35 volts input without any damage so you can make VU meter even you are new in electronic DIY. The circuit uses minimal component to make the job done. List of component: R1 = 1 kilo-ohms R2,R3 = 4.7 kilo-ohms R4 = 10 kilo-ohms ic = lm 3914n-1 (lm3914) C1 = 4.7 uf at least to 47 uf (better bass respond) 10 LEDs red,green,yellow,orange or whatever you want 9 - 12 volts DC power supply LM3914 schematic diagram    Lm3914 VU meter video, the video show step by step guide and circuit explanation. Now, I add a sine wave rectifier circuit to lm3914, it makes the dot mode more accuracy. Real dot mode VU meter schematic diagram
Read more