Helmet face sheild scratches repair.

-
This page shows you how to remove scratches from motocycle helmet face sheild. This method works well even the face sheild have so many scratches.
The helmet face sheild is easy to has scratches but you don't need to change it because you can remove it by yourself.

Normally, the helmet face shield made of plastic and a car polishing wax can remove scratches. However, the polishing wax dissolve some plastic and make it thinner so beware about it.
See video below for the instruction and prove.

Comments

Post a Comment

Popular posts from this blog

How to add power supply filter capacitor to amplifier board.

-
Image
I saw a new comment on my video, he asked me how to add a filter capacitor to amplifier board D.C. power supply. I think it's a good question so I will explain it here. What is a power supply filter capacitor? It is the capacitor that used to filter AC ripple from DC power supply present to amplifier board. If an amplifier has low capacitive power supply capacitor, it may present a little hum(50/60 Hz low-frequency sound) that you can hear in a quiet room. The capacitor also stores power and bring it instantly to your amplifier when an amplifier needs more power for a short period of time such as  explosion sound in a movie. However, If an amplifier has high-frequency power supply noise from a switching power supply, small capacitor need to parallel to a power supply and must be attached close to power amplifier IC as much as possible. Below pictures are the place that you add power supply capacitor. PAM 8610 board amplifier powe...
Read more

How to connect volume control to an amplifier

-
Image
I saw a comment on my Youtube video, he asked me how to connect any amplifier module to a volume control or potentiometer. I think so many people who want to start an electronic project must know this basic wiring too, I hope this wiring diagram will help an electronic DIYer like me. First thing you need to know: use shield wire for an input signal to volume control and from volume control to amplifier if you don't want you amplifier suffers from parasitic oscillation (sound like JeeeeJeeeee). keep a wiring as short as possible. use low resistive value volume control (5-10 kilo-ohms) if the amplifier has random parasitic noise when you turn a volume control up or down. volume control is a potentiometer. Volume control principle is a signal divider, the more volume control output(yellow line) near input signal source(pink line) the most signal flow to an amplifier. When you lower a volume control the resistive va...
Read more

Resistor color code

-
Image
A resistor is the most important electrical component in almost every electronic circuit, it can limit current to any load such as led, transistor, op-amp, etc.  We must read the resistor color code if we want to know the resistive value, tolerance, temperature coefficient. Resistors have different color bands (3,4,5,6) the more color bands the more resistor information. Now let's start with 3 bands resistor color code. The above resistor has only 3 bands First digit, Second digit, and multiply. A 3 bands resistor color code has a fixed +/- 20% tolerance which means if the color code value is 1,000 ohms the real-life resistive value may be +/- 200 ohms.  4 band resistor color code A 4 bands resistor color code has a tolerance value color strip, the resistor on the above picture has 5% tolerance. This type of resistor uses in a regular circuit such as television, radio, washing machine. 5 bands resistor color code A 5 bands resistor colo...
Read more

PAM 8403 board amp wiring diagram

-
Image
PAM 8403 is a portable 3 watts stereo class d amplifier that uses only 5 volts D.C. to operate. The amplifier board is easy to wiring and very small size, you can make a small amplifier project that not requires high voltages to work. The first thing you need to know. PAM 8403 cannot bridge together because the amplifier is already bridge-tie-load output configuration Over 6 volts can damage the amplifier module, if you want higher power you can check 10 watts class d amp PAM 8610 here You must use shield wire connect from input source to volume control and from volume control to the amplifier board input if you don't want your amplifier to suffer from parasitic oscillation (sound like JeeeeJeeee) Today I will show you how to wire PAM 8403 board amp that easy to understand. Let's see image below. You can see that two speakers do not share output ground like normal amplifier because PAM 8403 is a  bridge-tied-load amplifier, if each speaker wire touches eac...
Read more

simple bass booster circuit diagram

-
Image
This bass boost diagram is easy to build and work well, I made it because people asked me the schematic diagram of bass boost diagram on my youtube channel. The circuit has 9 dB gain@40 Hz that mean you will get good bass performance even you play music to a small speaker. Why this circuit doesn't look like circuits on the internet? Almost every circuit on the internet uses R/C filter between pre-amp and power amp stage to bypass high frequency to a ground and that seems audio signal being amplified and bypass to ground. I think it wastes pre-amplifier gain, the more gain preamp stage the more distortion to the audio signal, so I use a capacitor to send more negative feedback to pre-amp negative input when the frequency higher than cut-off frequency, capacitor impedance(resistance) higher when frequency lower and that make negative feedback decrease when frequency lower. An op-amp distortion lowers when negative feedback higher, that mean high-frequency disto...
Read more

10 watts 8 ohms class d amplifier pam8610 sound test

-
Image
Pam8610 IC is 10 watts @ 8 ohms (15 watts @ 4 ohms small heat sink require) stereo class d amplifier with very high efficiency over 90% and the amplifier works well without any heat sink at full power!!! . The amplifier board is very low cost ( around 1 $) but deliver 10 watts @ 8 ohms power from 13 volts power supply. As you can see in my video that the amp board require only one 100 uf electrolytic capacitor for supply decoupling to eliminate hum from switching power supply(some ic amplifier require 1000 uf to eliminate hum from the power supply). Sound testing: The amplifier sound good with good bass respond  good bass impact and well control (kick bass very good). High frequency clean, impact well and flat but lack transparent. Singer vocal is clean but not transparent. The sound stage is wide but space between instrument not precise. pam 8610 amp board is the quiet amp with very less hiss noise (5 cm away from tweeter to my ear :) which is not a big problem at all and ...
Read more

How to build high current hall effect sensor

-
Image
I published hall effect sensor circuit diagram and my audience asked me how to make a hall effect sensor that has a high current capability, so I made it for him and for all of you who want to build high current hall effect sensor. Normally, hall effect sensor used for detect magnetic field and send output to a microcontroller, that means any hall effect sensor doesn't need to have high current output. However, if you want to drive motor or any high current device without a microcontroller, this circuit is the best for you. List of components for this project: 1 x IRF 9540N (P channel MOSFET) 1 x A3144 hall effect sensor 1 x 1 kilo-ohms resistor 1 x 10 kilo-ohms resistor optional (use for led indicator) 1 x 1 kilo-ohms resistor 1 x White, red, blue or any other low current led Note: all resistor for this circuit is 1/4 watt, 20 % tolerance is ok with this circuit. The principle of this circuit: When hall effect sensor detects magnetic ...
Read more

How to make a simple audio pre-amplifier

-
Image
I saw a comment on my video that he wants a high-gain audio amplifier (1000 times or 60 dB voltage gain!!!). However, most commercial power amplifier IC has a maximum fix gain of around 200 times (lm386) which is far from 1000 times voltage gain, and the problem when you make a high gain amplifier is the high-frequency roll-off problem. The solution to the problem is making a pre-amplifier that has very low distortion, and wide bandwidth, and it can amplify audio signal around 10 times or 20 Dbs and send the audio signal to a power amplifier (the power amp IC he uses is tda7052 that has 40 dB or 100 times voltage gain). When combining the voltage gain of the two amplifiers, he will get 1000 times the voltage gain audio amplifier!!! The method is easy and uses minimum electronic components Breadboard wiring Audio preamplifier circuit diagram. Electronics component list: IC 1 = NE5534(op amp ic) R1, R2, C3 are amplifier gain control by negative feedbac...
Read more

15 watts stereo class T amplifier TA2024 sound test and review

-
Image
TA 2024 is low cost15 watts class T amplifier (I got it from eBay for 4.94$ free shipping). The amplifier board uses MKP film as input capacitor that hard to find in cheap board amplifier from eBay. The amplifier sound very clean and details and loud with high sensitivity loudspeaker (89 dB or better), bass not big but control well. However, high frequencies tend to roll off a little bit but still good. The TAta2024 amp is good with Jazz, pop, guitar solo, saxophone, and smooth jazz in my opinion. If you use switching power supply you need to add at least 2200 uf capacitor parallel to the power supply for best performance. TA 2024 specification: Class-T architecture  Single Supply Operation  “Audiophile” Quality Sound  0.04% THD+N @ 9W, 4Ω  0.18% IHF-IM @ 1W, 4Ω  11W @ 4Ω, 0.1% THD+N  6W @ 8Ω, 0.1% THD+N  15W @ 4Ω, 10% THD+N  10W @ 8Ω, 10% THD+N  High Efficiency  81% @ 15W, 4Ω  88% @ 10W, 8Ω  D...
Read more